Normal One Button Programming
- In the Bond Home application select + which is located bottom center in the Android application and top right in the iOS application.
- Select Remote Control.
- Choose the Bond Bridge you want this Fireplace device added to.
- Select Fireplace.
- Specific Information about your Fireplace Device.
- Select Location and choose from one of the predefined entries or add your own by selecting OTHER. When finished select Save.
- Select Device Name and enter the name for your device. When finished select OK to save.
- Please note that this name will be used for integrations so a simple easy to remember name is best.
- Select Continue.
- Choose the function to program.
- From the Add Functions screen, select Advanced settings.
- Select Signal type. ***The Bridge Pro is only RF***
- Choose RF or IR based on your remote
- If IR select IR and proceed to step 11
- If RF
- Make sure auto for the frequency is selected.
- Make sure Search remote database is on.
- Select Save.
- Press Start or next in the Bond Bridge application to start reading the signal.
- Press and release your remote's button you selected in step 7 above until the Bond Bridge center ring flashes green.
- When the system displays the test, test if it works. If so, click yes.
- Click Done.
- In the BOND application select the + (plus) sign.
- Select Remote Control then choose your bond
- Select Fireplace and set the location and device name and click Continue.
- Select the function you want to program
- Select "Start" and continue with the pairing process making sure the remote is within 2 feet of the Bond Bridge.
- If the Bond Bridge didn't detect the remote:
- If you pressed and held the button from the remote during programming, please try the steps again but this time repeatedly press and release the button.
- If the Bond Bridge didn't detect the remote:
- When the system displays the test functions, test if they work. If so, click yes or this is my remote.
- Click Done.
Remote frequency NOT detected by Bond Bridge
- In the Bond Home application select + which is located bottom center in the Android application and top right in the iOS application.
- Select Remote Control.
- Choose the Bond Bridge you want this Fireplace device added to.
- Select Fireplace.
- Specific Information about your Generic Device.
- Select Location and choose from one of the predefined entries or add your own by selecting OTHER. When finished select Save.
- Select Device Name and enter the name for your device. When finished select OK to save.
- Please note that this name will be used for integrations so a simple easy to remember name is best.
- Select Continue.
- Choose the function to program.
- From the Add Functions screen, select Advanced settings.
- Select Signal type. ***The Bridge Pro is only RF***
- Choose RF or IR based on your remote
- If IR select IR and proceed to step 13.
- If RF
- Choose RF.
- Select Auto for frequency. This will allow you to enter the frequency the bond bridge is trying to record.
- Enter your remote RF frequency. If there is information already entered, please backspace to remove first.
- The FCCID is generally located on the back of the remote.
- To see if the remote is support by the bond bridge, please go to https://bondhome.io/supported-devices/
- If the remote FCCID is not currently in the database, please go to FCCID lookup and enter the FCCID. Scroll down the page to see the FCCID. Input that information into step 2.3 above.
- Note - the Bond Bridge only supports frequencies from 300-450MHZ
- The FCCID is generally located on the back of the remote.
- Make sure Search remote database is ON.
- Select Save.
- Press Start or next in the Bond Bridge application to start reading the signal.
- Press and release your remote's button you selected in step 7 above until the Bond Bridge center ring flashes green.
- If the center ring doesn't flash green:
-
Use new remote batteries if at all possible to make sure it can support the programming.
-
please try the steps again but this time repeatedly press and release the button.
-
- If the center ring doesn't flash green:
- When the system displays the test, test if it works. If so, click yes.
- If your full remote is detected go to step 18
- Repeat Step 7 through 17 until all functions are programmed.
- Select Done.
If the steps above do not work, please use the steps below for setting the frequency of the remote.
-
Use new remote batteries if at all possible to make sure it can support the programming.
-
Press and hold the button from the remote during programming or if it doesn't record, please try the steps again but this time repeatedly press and release the button.
-
The remote must be next or close to the Bond when programming
Comments
Article is closed for comments.